Skip to main content

ASU Electronic Theses and Dissertations


This collection includes most of the ASU Theses and Dissertations from 2011 to present. ASU Theses and Dissertations are available in downloadable PDF format; however, a small percentage of items are under embargo. Information about the dissertations/theses includes degree information, committee members, an abstract, supporting data or media.

In addition to the electronic theses found in the ASU Digital Repository, ASU Theses and Dissertations can be found in the ASU Library Catalog.

Dissertations and Theses granted by Arizona State University are archived and made available through a joint effort of the ASU Graduate College and the ASU Libraries. For more information or questions about this collection contact or visit the Digital Repository ETD Library Guide or contact the ASU Graduate College at gradformat@asu.edu.


Contributor
Date Range
2010 2019


ABSTRACT As the technology length shrinks down, achieving higher gain is becoming very difficult in deep sub-micron technologies. As the supply voltages drop, cascodes are very difficult to implement and cascade amplifiers are needed to achieve sufficient gain with required output swing. This sets the fundamental limit on the SNR and hence the maximum resolution that can be achieved by ADC. With the RSD algorithm and the range overlap, the sub ADC can tolerate large comparator offsets leaving the linearity and accuracy requirement for the DAC and residue gain stage. Typically, the multiplying DAC requires high gain wide bandwidth op-amp …

Contributors
Swaminathan, Visu Vaithiyanathan, Barnaby, Hugh, Bakkaloglu, Bertan, et al.
Created Date
2012

The front end of almost all ADCs consists of a Sample and Hold Circuit in order to make sure a constant analog value is digitized at the end of ADC. The design of Track and Hold Circuit (THA) mainly focuses on following parameters: Input frequency, Sampling frequency, dynamic Range, hold pedestal, feed through error. This thesis will discuss the importance of these parameters of a THA to the ADCs and commonly used architectures of THA. A new architecture with SiGe HBT transistors in BiCMOS 130 nm technology is presented here. The proposed topology without complicated circuitry achieves high Spurious Free …

Contributors
Ramakrishna Rao, Nishita Ramakrishna, Barnaby, Hugh, Bakkaloglu, Bertan, et al.
Created Date
2012

During the last decades the development of the transistor and its continuous down-scaling allowed the appearance of cost effective wireless communication systems. New generation wideband wireless mobile systems demand high linearity, low power consumption and the low cost devices. Traditional RF systems are mainly analog-based circuitry. Contrary to digital circuits, the technology scaling results in reduction on the maximum voltage swing which makes RF design very challenging. Pushing the interface between the digital and analog boundary of the RF systems closer to the antenna becomes an attractive trend for modern RF devices. In order to take full advantages of the …

Contributors
Han, Yongping, Kiaei, Sayfe, Yu, Hongyu, et al.
Created Date
2012

The aging mechanism in devices is prone to uncertainties due to dynamic stress conditions. In AMS circuits these can lead to momentary fluctuations in circuit voltage that may be missed by a compact model and hence cause unpredictable failure. Firstly, multiple aging effects in the devices may have underlying correlations. The generation of new traps during TDDB may significantly accelerate BTI, since these traps are close to the dielectric-Si interface in scaled technology. Secondly, the prevalent reliability analysis lacks a direct validation of the lifetime of devices and circuits. The aging mechanism of BTI causes gradual degradation of the device …

Contributors
Patra, Devyani, Cao, Yu, Barnaby, Hugh, et al.
Created Date
2017

The non-quasi-static (NQS) description of device behavior is useful in fast switching and high frequency circuit applications. Hence, it is necessary to develop a fast and accurate compact NQS model for both large-signal and small-signal simulations. A new relaxation-time-approximation based NQS MOSFET model, consistent between transient and small-signal simulations, has been developed for surface-potential-based MOSFET compact models. The new model is valid for all regions of operation and is compatible with, and at low frequencies recovers, the quasi-static (QS) description of the MOSFET. The model is implemented in two widely used circuit simulators and tested for speed and convergence. It …

Contributors
Zhu, Zeqin, Gildenblat, Gennady, Bakkaloglu, Bertan, et al.
Created Date
2012

VCO as a ubiquitous circuit in many systems is highly demanding for the phase noises. Lowering the noise migrated from the power supply has been the trending topics for many years. Considering the Ring Oscillator(RO) based VCO is more sensitive to the supply noise, it is more significant to find out a useful technique to reduce the supply noise. Among the conventional supply noise reduction techniques such as filtering, channel length adjusting for the transistors, and the current noise mutual canceling, the new feature of the 28nm UTBB-FD-SOI process launched by the ST semiconductor offered a new method to reduce …

Contributors
Tang, Miao, Barnaby, Hugh, Bakkaloglu, Bertan, et al.
Created Date
2018

Scaling of the classical planar MOSFET below 20 nm gate length is facing not only technological difficulties but also limitations imposed by short channel effects, gate and junction leakage current due to quantum tunneling, high body doping induced threshold voltage variation, and carrier mobility degradation. Non-classical multiple-gate structures such as double-gate (DG) FinFETs and surrounding gate field-effect-transistors (SGFETs) have good electrostatic integrity and are an alternative to planar MOSFETs for below 20 nm technology nodes. Circuit design with these devices need compact models for SPICE simulation. In this work physics based compact models for the common-gate symmetric DG-FinFET, independent-gate asymmetric …

Contributors
Dessai, Gajanan, Gildenblat, Gennady, Gildenblat, Gennady, et al.
Created Date
2012

The thesis focuses on cost-efficient integration of the electro-chemical residue sensor (ECRS), a novel sensor developed for the in situ and real-time measurement of the residual impurities left on the wafer surface and in the fine structures of patterned wafers during typical rinse processes, and wireless transponder circuitry that is based on RFID technology. The proposed technology uses only the NMOS FD-SOI transistors with amorphous silicon as active material with silicon nitride as a gate dielectric. The proposed transistor was simulated under the SILVACO ATLAS Simulation Framework. A parametric study was performed to study the impact of different gate lengths …

Contributors
Pandit, Vedhas, Vermeire, Bert, Barnaby, Hugh, et al.
Created Date
2010

Efficiency of components is an ever increasing area of importance to portable applications, where a finite battery means finite operating time. Higher efficiency devices need to be designed that don't compromise on the performance that the consumer has come to expect. Class D amplifiers deliver on the goal of increased efficiency, but at the cost of distortion. Class AB amplifiers have low efficiency, but high linearity. By modulating the supply voltage of a Class AB amplifier to make a Class H amplifier, the efficiency can increase while still maintaining the Class AB level of linearity. A 92dB Power Supply Rejection …

Contributors
Peterson, Cory Jay, Bakkaloglu, Bertan, Barnaby, Hugh, et al.
Created Date
2013

In this work, a high resolution analog-to-digital converter (ADC) for use in harsh environments is presented. The ADC is implemented in bulk CMOS technology and is intended for space exploration, mining and automotive applications with a range of temperature variation in excess of 250°C. A continuous time (CT) sigma delta modulator employing a cascade of integrators with feed forward (CIFF) architecture in a single feedback loop topology is used for implementing the ADC. In order to enable operation in the intended application environments, an RC time constant tuning engine is proposed. The tuning engine is used to maintain linearity of …

Contributors
Anabtawi, Nijad, Barnaby, Hugh, Vermeire, Bert, et al.
Created Date
2011

Optical receivers have many different uses covering simple infrared receivers, high speed fiber optic communication and light based instrumentation. All of them have an optical receiver that converts photons to current followed by a transimpedance amplifier to convert the current to a useful voltage. Different systems create different requirements for each receiver. High speed digital communication require high throughput with enough sensitivity to keep the bit error rate low. Instrumentation receivers have a lower bandwidth, but higher gain and sensitivity requirements. In this thesis an optical receiver for use in instrumentation in presented. It is an entirely monolithic design with …

Contributors
Lafevre, Kyle, Bakkaloglu, Bertan, Barnaby, Hugh, et al.
Created Date
2011

In today's world there is a great need for sensing methods as tools to provide critical information to solve today's problems in security applications. Real time detection of trace chemicals, such as explosives, in a complex environment containing various interferents using a portable device that can be reliably deployed in a field has been a difficult challenge. A hybrid nanosensor based on the electrochemical reduction of trinitrotoluene (TNT) and the interaction of the reduction products with conducting polymer nanojunctions in an ionic liquid was fabricated. The sensor simultaneously measures the electrochemical current from the reduction of TNT and the conductance …

Contributors
Diaz Aguilar, Alvaro, Tao, Nongjian, Tsui, Raymond, et al.
Created Date
2012

In thesis, a test time reduction (a low cost test) methodology for digitally-calibrated pipeline analog-to-digital converters (ADCs) is presented. A long calibration time is required in the final test to validate performance of these designs. To reduce total test time, optimized calibration technique and calibrated effective number of bits (ENOB) prediction from calibration coefficient will be presented. With the prediction technique, failed devices can be identified only without actual calibration. This technique reduces significant amount of time for the total test time. Dissertation/Thesis

Contributors
Kim, Kibeom, Ozev, Sule, Kitchen, Jennifer, et al.
Created Date
2013

The existing compact models can reproduce the characteristics of MOSFETs in the temperature range of -40oC to 125oC. Some applications require circuits to operate over a wide temperature range consisting of temperatures below the specified range of existing compact models, requiring wide temperature range compact models for the design of such circuits. In order to develop wide temperature range compact models, fourteen different geometries of n-channel and p-channel MOSFETs manufactured in a 0.18μm mixed-signal process were electrically characterized over a temperature range of 40 K to 298 K. Electrical characterization included ID-VG and ID-VD under different drain, body and gate …

Contributors
Kathuria, Achal, Barnaby, Hugh, Schroder, Dieter K, et al.
Created Date
2010

Static CMOS logic has remained the dominant design style of digital systems for more than four decades due to its robustness and near zero standby current. Static CMOS logic circuits consist of a network of combinational logic cells and clocked sequential elements, such as latches and flip-flops that are used for sequencing computations over time. The majority of the digital design techniques to reduce power, area, and leakage over the past four decades have focused almost entirely on optimizing the combinational logic. This work explores alternate architectures for the flip-flops for improving the overall circuit performance, power and area. It …

Contributors
Yang, Jinghua, Vrudhula, Sarma, Barnaby, Hugh, et al.
Created Date
2018

The RADiation sensitive Field Effect Transistor (RADFET) has been conventionally used to measure radiation dose levels. These dose sensors are calibrated in such a way that a shift in threshold voltage, due to a build-up of oxide-trapped charge, can be used to estimate the radiation dose. In order to estimate the radiation dose level using RADFET, a wired readout circuit is necessary. Using the same principle of oxide-trapped charge build-up, but by monitoring the change in capacitance instead of threshold voltage, a wireless dose sensor can be developed. This RADiation sensitive CAPacitor (RADCAP) mounted on a resonant patch antenna can …

Contributors
Srinivasan Gopalan, Madusudanan, Barnaby, Hugh, Holbert, Keith, et al.
Created Date
2010

With the advent of parallel processing, primarily the time-interleaved pipeline ADCs, high speed and high resolution ADCs became a possibility. When these speeds touch giga samples per second and resolutions go beyond 12-bits, the parallelization becomes more extensive leading to repeated presence of several identical blocks in the architecture. This thesis discusses one such block, the sub-ADC (Flash ADC), of the pipeline and sharing it with more than two of the parallel processing channels thereby reducing area and power and input load capacitance to each stage. This work presents a design of 'sub-ADC shared in a time-interleaved pipeline ADC' in …

Contributors
Bikkina, Phaneendra Kumar, Barnaby, Hugh, Mikkola, Esko, et al.
Created Date
2013

Programmable metallization cell (PMC) technology employs the mechanisms of metal ion transport in solid electrolytes (SE) and electrochemical redox reactions in order to form metallic electrodeposits. When a positive bias is applied to an anode opposite to a cathode, atoms at the anode are oxidized to ions and dissolve into the SE. Under the influence of the electric field, the ions move to the cathode and become reduced to form the electrodeposits. These electrodeposits are filamentary in nature and persistent, and since they are metallic can alter the physical characteristics of the material on which they are formed. PMCs can …

Contributors
Yu, Weijie, Kozicki, Michael N, Barnaby, Hugh, et al.
Created Date
2015

With the natural resources of earth depleting very fast, the natural resources of other celestial bodies are considered a potential replacement. Thus, there has been rise of space missions constantly and with it the need of more sophisticated spectrometer devices has increased. The most important requirement in such an application is low area and power consumption. To save area, some scintillators have been developed that can resolve both neutrons and gamma events rather than traditional scintillators which can do only one of these and thus, the spacecraft needs two such devices. But with this development, the requirements out of the …

Contributors
Gupta, Kush, Barnaby, Hugh, Hardgrove, Craig, et al.
Created Date
2017

A fully automated logic design methodology for radiation hardened by design (RHBD) high speed logic using fine grained triple modular redundancy (TMR) is presented. The hardening techniques used in the cell library are described and evaluated, with a focus on both layout techniques that mitigate total ionizing dose (TID) and latchup issues and flip-flop designs that mitigate single event transient (SET) and single event upset (SEU) issues. The base TMR self-correcting master-slave flip-flop is described and compared to more traditional hardening techniques. Additional refinements are presented, including testability features that disable the self-correction to allow detection of manufacturing defects. The …

Contributors
Hindman, Nathan David, Clark, Lawrence T, Holbert, Keith, et al.
Created Date
2012

The rapid improvement in computation capability has made deep convolutional neural networks (CNNs) a great success in recent years on many computer vision tasks with significantly improved accuracy. During the inference phase, many applications demand low latency processing of one image with strict power consumption requirement, which reduces the efficiency of GPU and other general-purpose platform, bringing opportunities for specific acceleration hardware, e.g. FPGA, by customizing the digital circuit specific for the deep learning algorithm inference. However, deploying CNNs on portable and embedded systems is still challenging due to large data volume, intensive computation, varying algorithm structures, and frequent memory …

Contributors
Ma, Yufei, Vrudhula, Sarma, Seo, Jae-sun, et al.
Created Date
2018

The market for high speed camera chips, or image sensors, has experienced rapid growth over the past decades owing to its broad application space in security, biomedical equipment, and mobile devices. CMOS (complementary metal-oxide-semiconductor) technology has significantly improved the performance of the high speed camera chip by enabling the monolithic integration of pixel circuits and on-chip analog-to-digital conversion. However, for low light intensity applications, many CMOS image sensors have a sub-optimum dynamic range, particularly in high speed operation. Thus the requirements for a sensor to have a high frame rate and high fill factor is attracting more attention. Another drawback …

Contributors
Zhao, Tong, Barnaby, Hugh, Mikkola, Esko, et al.
Created Date
2017

Counterfeiting of goods is a widespread epidemic that is affecting the world economy. The conventional labeling techniques are proving inadequate to thwart determined counterfeiters equipped with sophisticated technologies. There is a growing need of a secure labeling that is easy to manufacture and analyze but extremely difficult to copy. Programmable metallization cell technology operates on a principle of controllable reduction of a metal ions to an electrodeposit in a solid electrolyte by application of bias. The nature of metallic electrodeposit is unique for each instance of growth, moreover it has a treelike, bifurcating fractal structure with high information capacity. These …

Contributors
Chamele, Ninad, Kozicki, Michael, Barnaby, Hugh, et al.
Created Date
2017

Programmable Metallization Cell (PMC) is a technology platform which utilizes mass transport in solid or liquid electrolyte coupled with electrochemical (redox) reactions to form or remove nanoscale metallic electrodeposits on or in the electrolyte. The ability to redistribute metal mass and form metallic nanostructure in or on a structure in situ, via the application of a bias on laterally placed electrodes, creates a large number of promising applications. A novel PMC-based lateral microwave switch was fabricated and characterized for use in microwave systems. It has demonstrated low insertion loss, high isolation, low voltage operation, low power and low energy consumption, …

Contributors
Ren, Minghan, Kozicki, Michael, Schroder, Dieter, et al.
Created Date
2011

The medical industry has benefited greatly by electronic integration resulting in the explosive growth of active medical implants. These devices often treat and monitor chronic health conditions and require very minimal power usage. A key part of these medical implants is an ultra-low power two way wireless communication system. This enables both control of the implant as well as relay of information collected. This research has focused on a high performance receiver for medical implant applications. One commonly quoted specification to compare receivers is energy per bit required. This metric is useful, but incomplete in that it ignores Sensitivity level, …

Contributors
Stevens, Mark A., Kiaei, Sayfe, Bakkaloglu, Bertan, et al.
Created Date
2012

Negative Bias Temperature Instability (NBTI) is commonly seen in p-channel transistors under negative gate voltages at an elevated temperature. The interface traps, oxide traps and NBTI mechanisms are discussed and their effect on circuit degradation and results are discussed. This thesis focuses on developing a model for simulating impact of NBTI effects at circuit level. The model mimics the effects of degradation caused by the defects. The NBTI model developed in this work is validated and sanity checked by using the simulation data from silvaco and gives excellent results. Furthermore the susceptibility of CMOS circuits such as the CMOS inverter, …

Contributors
Padala, Sudheer, Barnaby, Hugh, Bakkaloglu, Bertan, et al.
Created Date
2014

This thesis describes the design of a Single Event Transient (SET) duration measurement test-structure on the Global Foundries (previously IBM) 32-nm silicon-on insulator (SOI) process. The test structure is designed for portability and allows quick design and implementation on a new process node. Such a test structure is critical in analyzing the effects of radiation on complementary metal oxide semi-conductor (CMOS) circuits. The focus of this thesis is the change in pulse width during propagation of SET pulse and build a test structure to measure the duration of a SET pulse generated in real time. This test structure can estimate …

Contributors
Masand, Lovish, Clark, Lawrence, Holbert, Keith, et al.
Created Date
2017

The dissolution of metal layers such as silver into chalcogenide glass layers such as germanium selenide changes the resistivity of the metal and chalcogenide films by a great extent. It is known that the incorporation of the metal can be achieved by ultra violet light exposure or thermal processes. In this work, the use of metal dissolution by exposure to gamma radiation has been explored for radiation sensor applications. Test structures were designed and a process flow was developed for prototype sensor fabrication. The test structures were designed such that sensitivity to radiation could be studied. The focus is on …

Contributors
Chandran, Ankitha, Kozicki, Michael N, Holbert, Keith, et al.
Created Date
2012

Over decades, scientists have been scaling devices to increasingly smaller feature sizes for ever better performance of complementary metal-oxide semiconductor (CMOS) technology to meet requirements on speed, complexity, circuit density, power consumption and ultimately cost required by many advanced applications. However, going to these ultra-scaled CMOS devices also brings some drawbacks. Aging due to bias-temperature-instability (BTI) and Hot carrier injection (HCI) is the dominant cause of functional failure in large scale logic circuits. The aging phenomena, on top of process variations, translate into complexity and reduced design margin for circuits. Such issues call for “Design for Reliability”. In order to …

Contributors
BANSAL, ANKITA, Cao, Yu, Seo, Jae Sun, et al.
Created Date
2016

ABSTRACT Developing new non-traditional device models is gaining popularity as the silicon-based electrical device approaches its limitation when it scales down. Membrane systems, also called P systems, are a new class of biological computation model inspired by the way cells process chemical signals. Spiking Neural P systems (SNP systems), a certain kind of membrane systems, is inspired by the way the neurons in brain interact using electrical spikes. Compared to the traditional Boolean logic, SNP systems not only perform similar functions but also provide a more promising solution for reliable computation. Two basic neuron types, Low Pass (LP) neurons and …

Contributors
An, Pei, Cao, Yu, Barnaby, Hugh, et al.
Created Date
2013

Non-volatile memory (NVM) has become a staple in the everyday life of consumers. NVM manifests inside cell phones, laptops, and most recently, wearable tech such as smart watches. NAND Flash has been an excellent solution to conditions requiring fast, compact NVM. Current technology nodes are nearing the physical limits of scaling, preventing flash from improving. To combat the limitations of flash and to appease consumer demand for progressively faster and denser NVM, new technologies are needed. One possible candidate for the replacement of NAND Flash is programmable metallization cells (PMC). PMC are a type of resistive memory, meaning that they …

Contributors
Taggart, Jennifer Lynn, Barnaby, Hugh, Kozicki, Michael, et al.
Created Date
2015

Lateral Double-diffused (LDMOS) transistors are commonly used in power management, high voltage/current, and RF circuits. Their characteristics include high breakdown voltage, low on-resistance, and compatibility with standard CMOS and BiCMOS manufacturing processes. As with other semiconductor devices, an accurate and physical compact model is critical for LDMOS-based circuit design. The goal of this research work is to advance the state-of-the-art by developing a physics-based scalable compact model of LDMOS transistors. The new model, SP-HV, is constructed from a surface-potential-based bulk MOSFET model, PSP, and a nonlinear resistor model, R3. The use of independently verified and mature sub-models leads to increased …

Contributors
Yao, Wei, Gildenblat, Gennady, Barnaby, Hugh, et al.
Created Date
2012

Semiconductor memory is a key component of the computing systems. Beyond the conventional memory and data storage applications, in this dissertation, both mainstream and eNVM memory technologies are explored for radiation environment, hardware security system and machine learning applications. In the radiation environment, e.g. aerospace, the memory devices face different energetic particles. The strike of these energetic particles can generate electron-hole pairs (directly or indirectly) as they pass through the semiconductor device, resulting in photo-induced current, and may change the memory state. First, the trend of radiation effects of the mainstream memory technologies with technology node scaling is reviewed. Then, …

Contributors
LIU, RUI, Yu, Shimeng, Yu, Shimeng, et al.
Created Date
2018

The formation of dendrites in materials is usually seen as a failure-inducing defect in devices. Naturally, most research views dendrites as a problem needing a solution while focusing on process control techniques and post-mortem analysis of various stress patterns with the ultimate goal of total suppression of the structures. However, programmable metallization cell (PMC) technology embraces dendrite formation in chalcogenide glasses by utilizing the nascent conductive filaments as its core operative element. Furthermore, exciting More-than-Moore capabilities in the realms of device watermarking and hardware encryption schema are made possible by the random nature of dendritic branch growth. While dendritic structures …

Contributors
Foss, Ryan Martin, Kozicki, Michael N, Barnaby, Hugh, et al.
Created Date
2016

Nonvolatile memory (NVM) technologies have been an integral part of electronic systems for the past 30 years. The ideal non-volatile memory have minimal physical size, energy usage, and cost while having maximal speed, capacity, retention time, and radiation hardness. A promising candidate for next-generation memory is ion-conducting bridging RAM which is referred to as programmable metallization cell (PMC), conductive bridge RAM (CBRAM), or electrochemical metallization memory (ECM), which is likely to surpass flash memory in all the ideal memory characteristics. A comprehensive physics-based model is needed to completely understand PMC operation and assist in design optimization. To advance the PMC …

Contributors
Rajabi, Saba, Barnaby, Hugh, Kozicki, Michael, et al.
Created Date
2014

The scaling of transistors has numerous advantages such as increased memory density, less power consumption and better performance; but on the other hand, they also give rise to many reliability issues. One of the major reliability issue is the hot carrier injection and the effect it has on device degradation over time which causes serious circuit malfunctions. Hot carrier injection has been studied from early 1980's and a lot of research has been done on the various hot carrier injection mechanisms and how the devices get damaged due to this effect. However, most of the existing hot carrier degradation models …

Contributors
Muthuseenu, Kiraneswar, Barnaby, Hugh, Kozicki, Michael, et al.
Created Date
2017

The advent of threshold logic simplifies the traditional Boolean logic to the single level multi-input function. Threshold logic latch (TLL), among implementations of threshold logic, is functionally equivalent to a multi-input function with an edge triggered flip-flop, which stands out to improve area and both dynamic and leakage power consumption, providing an appropriate design alternative. Accordingly, the TLL standard cell library is designed. Through technology mapping, hybrid circuit is generated by absorbing the logic cone backward from each flip-flip to get the smallest remaining feeder. With the scan test methodology adopted, design for testability (DFT) is proposed, including scan element …

Contributors
Hu, Yang, Vrudhula, Sarma, Barnaby, Hugh, et al.
Created Date
2013

New technologies enable the exploration of space, high-fidelity defense systems, lighting fast intercontinental communication systems as well as medical technologies that extend and improve patient lives. The basis for these technologies is high reliability electronics devised to meet stringent design goals and to operate consistently for many years deployed in the field. An on-going concern for engineers is the consequences of ionizing radiation exposure, specifically total dose effects. For many of the different applications, there is a likelihood of exposure to radiation, which can result in device degradation and potentially failure. While the total dose effects and the resulting degradation …

Contributors
Schlenvogt, Garrett James, Barnaby, Hugh, Goodnick, Stephen, et al.
Created Date
2014

Space exploration is a large field that requires high performing circuitry due to the harsh environment. Within a space environment one of the biggest factors leading to circuit failure is radiation. Circuits must be robust enough to continue operation after being exposed to the high doses of radiation. Bandgap reference (BGR) circuits are designed to be voltage references that stay stable across a wide range of supply voltages and temperatures. A bandgap reference is a piece of a large circuit that supplies critical elements of the large circuit with a constant voltage. When used in a space environment with large …

Contributors
Davis, Parker William, Barnaby, Hugh, Kitchen, Jennifer, et al.
Created Date
2019

There is an ever growing need for larger memories which are reliable and fast. New technologies to implement non-volatile memories which are large, fast, compact and cost-efficient are being studied extensively. One of the most promising technologies being developed is the resistive RAM (ReRAM). In ReRAM the resistance of the device varies with the voltage applied across it. Programmable metallization cells (PMC) is one of the devices belonging to this category of non-volatile memories. In order to advance the development of these devices, there is a need to develop simulation models which replicate the behavior of these devices in circuits. …

Contributors
Bharadwaj, Vineeth, Barnaby, Hugh, Kozicki, Michael, et al.
Created Date
2014