Skip to main content

ASU Electronic Theses and Dissertations


This collection includes most of the ASU Theses and Dissertations from 2011 to present. ASU Theses and Dissertations are available in downloadable PDF format; however, a small percentage of items are under embargo. Information about the dissertations/theses includes degree information, committee members, an abstract, supporting data or media.

In addition to the electronic theses found in the ASU Digital Repository, ASU Theses and Dissertations can be found in the ASU Library Catalog.

Dissertations and Theses granted by Arizona State University are archived and made available through a joint effort of the ASU Graduate College and the ASU Libraries. For more information or questions about this collection contact or visit the Digital Repository ETD Library Guide or contact the ASU Graduate College at gradformat@asu.edu.


Contributor
Date Range
2010 2019


ABSTRACT As the technology length shrinks down, achieving higher gain is becoming very difficult in deep sub-micron technologies. As the supply voltages drop, cascodes are very difficult to implement and cascade amplifiers are needed to achieve sufficient gain with required output swing. This sets the fundamental limit on the SNR and hence the maximum resolution that can be achieved by ADC. With the RSD algorithm and the range overlap, the sub ADC can tolerate large comparator offsets leaving the linearity and accuracy requirement for the DAC and residue gain stage. Typically, the multiplying DAC requires high gain wide bandwidth op-amp …

Contributors
Swaminathan, Visu Vaithiyanathan, Barnaby, Hugh, Bakkaloglu, Bertan, et al.
Created Date
2012

The front end of almost all ADCs consists of a Sample and Hold Circuit in order to make sure a constant analog value is digitized at the end of ADC. The design of Track and Hold Circuit (THA) mainly focuses on following parameters: Input frequency, Sampling frequency, dynamic Range, hold pedestal, feed through error. This thesis will discuss the importance of these parameters of a THA to the ADCs and commonly used architectures of THA. A new architecture with SiGe HBT transistors in BiCMOS 130 nm technology is presented here. The proposed topology without complicated circuitry achieves high Spurious Free …

Contributors
Ramakrishna Rao, Nishita Ramakrishna, Barnaby, Hugh, Bakkaloglu, Bertan, et al.
Created Date
2012

During the last decades the development of the transistor and its continuous down-scaling allowed the appearance of cost effective wireless communication systems. New generation wideband wireless mobile systems demand high linearity, low power consumption and the low cost devices. Traditional RF systems are mainly analog-based circuitry. Contrary to digital circuits, the technology scaling results in reduction on the maximum voltage swing which makes RF design very challenging. Pushing the interface between the digital and analog boundary of the RF systems closer to the antenna becomes an attractive trend for modern RF devices. In order to take full advantages of the …

Contributors
Han, Yongping, Kiaei, Sayfe, Yu, Hongyu, et al.
Created Date
2012

The aging mechanism in devices is prone to uncertainties due to dynamic stress conditions. In AMS circuits these can lead to momentary fluctuations in circuit voltage that may be missed by a compact model and hence cause unpredictable failure. Firstly, multiple aging effects in the devices may have underlying correlations. The generation of new traps during TDDB may significantly accelerate BTI, since these traps are close to the dielectric-Si interface in scaled technology. Secondly, the prevalent reliability analysis lacks a direct validation of the lifetime of devices and circuits. The aging mechanism of BTI causes gradual degradation of the device …

Contributors
Patra, Devyani, Cao, Yu, Barnaby, Hugh, et al.
Created Date
2017

The non-quasi-static (NQS) description of device behavior is useful in fast switching and high frequency circuit applications. Hence, it is necessary to develop a fast and accurate compact NQS model for both large-signal and small-signal simulations. A new relaxation-time-approximation based NQS MOSFET model, consistent between transient and small-signal simulations, has been developed for surface-potential-based MOSFET compact models. The new model is valid for all regions of operation and is compatible with, and at low frequencies recovers, the quasi-static (QS) description of the MOSFET. The model is implemented in two widely used circuit simulators and tested for speed and convergence. It …

Contributors
Zhu, Zeqin, Gildenblat, Gennady, Bakkaloglu, Bertan, et al.
Created Date
2012

VCO as a ubiquitous circuit in many systems is highly demanding for the phase noises. Lowering the noise migrated from the power supply has been the trending topics for many years. Considering the Ring Oscillator(RO) based VCO is more sensitive to the supply noise, it is more significant to find out a useful technique to reduce the supply noise. Among the conventional supply noise reduction techniques such as filtering, channel length adjusting for the transistors, and the current noise mutual canceling, the new feature of the 28nm UTBB-FD-SOI process launched by the ST semiconductor offered a new method to reduce …

Contributors
Tang, Miao, Barnaby, Hugh, Bakkaloglu, Bertan, et al.
Created Date
2018

Scaling of the classical planar MOSFET below 20 nm gate length is facing not only technological difficulties but also limitations imposed by short channel effects, gate and junction leakage current due to quantum tunneling, high body doping induced threshold voltage variation, and carrier mobility degradation. Non-classical multiple-gate structures such as double-gate (DG) FinFETs and surrounding gate field-effect-transistors (SGFETs) have good electrostatic integrity and are an alternative to planar MOSFETs for below 20 nm technology nodes. Circuit design with these devices need compact models for SPICE simulation. In this work physics based compact models for the common-gate symmetric DG-FinFET, independent-gate asymmetric …

Contributors
Dessai, Gajanan, Gildenblat, Gennady, Gildenblat, Gennady, et al.
Created Date
2012

The thesis focuses on cost-efficient integration of the electro-chemical residue sensor (ECRS), a novel sensor developed for the in situ and real-time measurement of the residual impurities left on the wafer surface and in the fine structures of patterned wafers during typical rinse processes, and wireless transponder circuitry that is based on RFID technology. The proposed technology uses only the NMOS FD-SOI transistors with amorphous silicon as active material with silicon nitride as a gate dielectric. The proposed transistor was simulated under the SILVACO ATLAS Simulation Framework. A parametric study was performed to study the impact of different gate lengths …

Contributors
Pandit, Vedhas, Vermeire, Bert, Barnaby, Hugh, et al.
Created Date
2010

Efficiency of components is an ever increasing area of importance to portable applications, where a finite battery means finite operating time. Higher efficiency devices need to be designed that don't compromise on the performance that the consumer has come to expect. Class D amplifiers deliver on the goal of increased efficiency, but at the cost of distortion. Class AB amplifiers have low efficiency, but high linearity. By modulating the supply voltage of a Class AB amplifier to make a Class H amplifier, the efficiency can increase while still maintaining the Class AB level of linearity. A 92dB Power Supply Rejection …

Contributors
Peterson, Cory Jay, Bakkaloglu, Bertan, Barnaby, Hugh, et al.
Created Date
2013

In this work, a high resolution analog-to-digital converter (ADC) for use in harsh environments is presented. The ADC is implemented in bulk CMOS technology and is intended for space exploration, mining and automotive applications with a range of temperature variation in excess of 250°C. A continuous time (CT) sigma delta modulator employing a cascade of integrators with feed forward (CIFF) architecture in a single feedback loop topology is used for implementing the ADC. In order to enable operation in the intended application environments, an RC time constant tuning engine is proposed. The tuning engine is used to maintain linearity of …

Contributors
Anabtawi, Nijad, Barnaby, Hugh, Vermeire, Bert, et al.
Created Date
2011

Optical receivers have many different uses covering simple infrared receivers, high speed fiber optic communication and light based instrumentation. All of them have an optical receiver that converts photons to current followed by a transimpedance amplifier to convert the current to a useful voltage. Different systems create different requirements for each receiver. High speed digital communication require high throughput with enough sensitivity to keep the bit error rate low. Instrumentation receivers have a lower bandwidth, but higher gain and sensitivity requirements. In this thesis an optical receiver for use in instrumentation in presented. It is an entirely monolithic design with …

Contributors
Lafevre, Kyle, Bakkaloglu, Bertan, Barnaby, Hugh, et al.
Created Date
2011

In today's world there is a great need for sensing methods as tools to provide critical information to solve today's problems in security applications. Real time detection of trace chemicals, such as explosives, in a complex environment containing various interferents using a portable device that can be reliably deployed in a field has been a difficult challenge. A hybrid nanosensor based on the electrochemical reduction of trinitrotoluene (TNT) and the interaction of the reduction products with conducting polymer nanojunctions in an ionic liquid was fabricated. The sensor simultaneously measures the electrochemical current from the reduction of TNT and the conductance …

Contributors
Diaz Aguilar, Alvaro, Tao, Nongjian, Tsui, Raymond, et al.
Created Date
2012

In thesis, a test time reduction (a low cost test) methodology for digitally-calibrated pipeline analog-to-digital converters (ADCs) is presented. A long calibration time is required in the final test to validate performance of these designs. To reduce total test time, optimized calibration technique and calibrated effective number of bits (ENOB) prediction from calibration coefficient will be presented. With the prediction technique, failed devices can be identified only without actual calibration. This technique reduces significant amount of time for the total test time. Dissertation/Thesis

Contributors
Kim, Kibeom, Ozev, Sule, Kitchen, Jennifer, et al.
Created Date
2013

The existing compact models can reproduce the characteristics of MOSFETs in the temperature range of -40oC to 125oC. Some applications require circuits to operate over a wide temperature range consisting of temperatures below the specified range of existing compact models, requiring wide temperature range compact models for the design of such circuits. In order to develop wide temperature range compact models, fourteen different geometries of n-channel and p-channel MOSFETs manufactured in a 0.18μm mixed-signal process were electrically characterized over a temperature range of 40 K to 298 K. Electrical characterization included ID-VG and ID-VD under different drain, body and gate …

Contributors
Kathuria, Achal, Barnaby, Hugh, Schroder, Dieter K, et al.
Created Date
2010

Static CMOS logic has remained the dominant design style of digital systems for more than four decades due to its robustness and near zero standby current. Static CMOS logic circuits consist of a network of combinational logic cells and clocked sequential elements, such as latches and flip-flops that are used for sequencing computations over time. The majority of the digital design techniques to reduce power, area, and leakage over the past four decades have focused almost entirely on optimizing the combinational logic. This work explores alternate architectures for the flip-flops for improving the overall circuit performance, power and area. It …

Contributors
Yang, Jinghua, Vrudhula, Sarma, Barnaby, Hugh, et al.
Created Date
2018

The RADiation sensitive Field Effect Transistor (RADFET) has been conventionally used to measure radiation dose levels. These dose sensors are calibrated in such a way that a shift in threshold voltage, due to a build-up of oxide-trapped charge, can be used to estimate the radiation dose. In order to estimate the radiation dose level using RADFET, a wired readout circuit is necessary. Using the same principle of oxide-trapped charge build-up, but by monitoring the change in capacitance instead of threshold voltage, a wireless dose sensor can be developed. This RADiation sensitive CAPacitor (RADCAP) mounted on a resonant patch antenna can …

Contributors
Srinivasan Gopalan, Madusudanan, Barnaby, Hugh, Holbert, Keith, et al.
Created Date
2010

With the advent of parallel processing, primarily the time-interleaved pipeline ADCs, high speed and high resolution ADCs became a possibility. When these speeds touch giga samples per second and resolutions go beyond 12-bits, the parallelization becomes more extensive leading to repeated presence of several identical blocks in the architecture. This thesis discusses one such block, the sub-ADC (Flash ADC), of the pipeline and sharing it with more than two of the parallel processing channels thereby reducing area and power and input load capacitance to each stage. This work presents a design of 'sub-ADC shared in a time-interleaved pipeline ADC' in …

Contributors
Bikkina, Phaneendra Kumar, Barnaby, Hugh, Mikkola, Esko, et al.
Created Date
2013

Programmable metallization cell (PMC) technology employs the mechanisms of metal ion transport in solid electrolytes (SE) and electrochemical redox reactions in order to form metallic electrodeposits. When a positive bias is applied to an anode opposite to a cathode, atoms at the anode are oxidized to ions and dissolve into the SE. Under the influence of the electric field, the ions move to the cathode and become reduced to form the electrodeposits. These electrodeposits are filamentary in nature and persistent, and since they are metallic can alter the physical characteristics of the material on which they are formed. PMCs can …

Contributors
Yu, Weijie, Kozicki, Michael N, Barnaby, Hugh, et al.
Created Date
2015

With the natural resources of earth depleting very fast, the natural resources of other celestial bodies are considered a potential replacement. Thus, there has been rise of space missions constantly and with it the need of more sophisticated spectrometer devices has increased. The most important requirement in such an application is low area and power consumption. To save area, some scintillators have been developed that can resolve both neutrons and gamma events rather than traditional scintillators which can do only one of these and thus, the spacecraft needs two such devices. But with this development, the requirements out of the …

Contributors
Gupta, Kush, Barnaby, Hugh, Hardgrove, Craig, et al.
Created Date
2017

A fully automated logic design methodology for radiation hardened by design (RHBD) high speed logic using fine grained triple modular redundancy (TMR) is presented. The hardening techniques used in the cell library are described and evaluated, with a focus on both layout techniques that mitigate total ionizing dose (TID) and latchup issues and flip-flop designs that mitigate single event transient (SET) and single event upset (SEU) issues. The base TMR self-correcting master-slave flip-flop is described and compared to more traditional hardening techniques. Additional refinements are presented, including testability features that disable the self-correction to allow detection of manufacturing defects. The …

Contributors
Hindman, Nathan David, Clark, Lawrence T, Holbert, Keith, et al.
Created Date
2012