Skip to main content

ASU Electronic Theses and Dissertations


This collection includes most of the ASU Theses and Dissertations from 2011 to present. ASU Theses and Dissertations are available in downloadable PDF format; however, a small percentage of items are under embargo. Information about the dissertations/theses includes degree information, committee members, an abstract, supporting data or media.

In addition to the electronic theses found in the ASU Digital Repository, ASU Theses and Dissertations can be found in the ASU Library Catalog.

Dissertations and Theses granted by Arizona State University are archived and made available through a joint effort of the ASU Graduate College and the ASU Libraries. For more information or questions about this collection contact or visit the Digital Repository ETD Library Guide or contact the ASU Graduate College at gradformat@asu.edu.


Subject
Date Range
2011 2019


A computational framework based on convex optimization is presented for stability analysis of systems described by Partial Differential Equations (PDEs). Specifically, two forms of linear PDEs with spatially distributed polynomial coefficients are considered. The first class includes linear coupled PDEs with one spatial variable. Parabolic, elliptic or hyperbolic PDEs with Dirichlet, Neumann, Robin or mixed boundary conditions can be reformulated in order to be used by the framework. As an example, the reformulation is presented for systems governed by Schr¨odinger equation, parabolic type, relativistic heat conduction PDE and acoustic wave equation, hyperbolic types. The second form of PDEs of interest …

Contributors
Meyer, Evgeny, Peet, Matthew, Berman, Spring, et al.
Created Date
2016

Stereolithography files (STL) are widely used in diverse fields as a means of describing complex geometries through surface triangulations. The resulting stereolithography output is a result of either experimental measurements, or computer-aided design. Often times stereolithography outputs from experimental means are prone to noise, surface irregularities and holes in an otherwise closed surface. A general method for denoising and adaptively smoothing these dirty stereolithography files is proposed. Unlike existing means, this approach aims to smoothen the dirty surface representation by utilizing the well established levelset method. The level of smoothing and denoising can be set depending on a per-requirement basis …

Contributors
Kannan, Karthik, Herrmann, Marcus, Peet, Yulia, et al.
Created Date
2014

Structural integrity is an important characteristic of performance for critical components used in applications such as aeronautics, materials, construction and transportation. When appraising the structural integrity of these components, evaluation methods must be accurate. In addition to possessing capability to perform damage detection, the ability to monitor the level of damage over time can provide extremely useful information in assessing the operational worthiness of a structure and in determining whether the structure should be repaired or removed from service. In this work, a sequential Bayesian approach with active sensing is employed for monitoring crack growth within fatigue-loaded materials. The monitoring …

Contributors
Huff, Daniel William, Papandreou-Suppappola, Antonia, Kovvali, Narayan, et al.
Created Date
2013

Although high performance, light-weight composites are increasingly being used in applications ranging from aircraft, rotorcraft, weapon systems and ground vehicles, the assurance of structural reliability remains a critical issue. In composites, damage is absorbed through various fracture processes, including fiber failure, matrix cracking and delamination. An important element in achieving reliable composite systems is a strong capability of assessing and inspecting physical damage of critical structural components. Installation of a robust Structural Health Monitoring (SHM) system would be very valuable in detecting the onset of composite failure. A number of major issues still require serious attention in connection with the …

Contributors
Moncada, Albert, Chattopadhyay, Aditi, Dai, Lenore, et al.
Created Date
2012

Composite materials are increasingly being used in aircraft, automobiles, and other applications due to their high strength to weight and stiffness to weight ratios. However, the presence of damage, such as delamination or matrix cracks, can significantly compromise the performance of these materials and result in premature failure. Structural components are often manually inspected to detect the presence of damage. This technique, known as schedule based maintenance, however, is expensive, time-consuming, and often limited to easily accessible structural elements. Therefore, there is an increased demand for robust and efficient Structural Health Monitoring (SHM) techniques that can be used for Condition …

Contributors
Vizzini Ii, Anthony James, Chattopadhyay, Aditi, Fard, Masoud, et al.
Created Date
2012

The subject of this thesis is concerned with the amount of cooling air assigned to seal high pressure turbine rim cavities which is critical for performance as well as component life. Insufficient air leads to excessive hot annulus gas ingestion and its penetration deep into the cavity compromising disc life. Excessive purge air, adversely affects performance. Experiments on a rotating turbine stage rig which included a rotor-stator forward disc cavity were performed at Arizona State University. The turbine rig has 22 vanes and 28 blades, while the rim cavity is composed of a single-tooth rim lab seal and a rim …

Contributors
Kanjiyani, Shezan, Lee, Taewoo, Mirzamoghadam, Alexander, et al.
Created Date
2016

Unmanned aerial vehicles have received increased attention in the last decade due to their versatility, as well as the availability of inexpensive sensors (e.g. GPS, IMU) for their navigation and control. Multirotor vehicles, specifically quadrotors, have formed a fast growing field in robotics, with the range of applications spanning from surveil- lance and reconnaissance to agriculture and large area mapping. Although in most applications single quadrotors are used, there is an increasing interest in architectures controlling multiple quadrotors executing a collaborative task. This thesis introduces a new concept of control involving more than one quadrotors, according to which two quadrotors …

Contributors
Larsson, Daniel, Artemiadis, Panagiotis, Marvi, Hamidreza, et al.
Created Date
2016

This paper describes an effort to bring wing structural stiffness and aeroelastic considerations early in the conceptual design process with an automated tool. Stiffness and aeroelasticity can be well represented with a stochastic model during conceptual design because of the high level of uncertainty and variability in wing non-structural mass such as fuel loading and control surfaces. To accomplish this, an improvement is made to existing design tools utilizing rule based automated design to generate wing torque box geometry from a specific wing outer mold-line. Simple analysis on deflection and inferred stiffness shows how early conceptual design choices can strongly …

Contributors
Miskin, Daniel L, Takahashi, Timothy T, Mignolet, Marc, et al.
Created Date
2018

The advancements in additive manufacturing have made it possible to bring life to designs that would otherwise exist only on paper. An excellent example of such designs are the Triply Periodic Minimal Surface (TPMS) structures like Schwarz D, Schwarz P, Gyroid, etc. These structures are self-sustaining, i.e. they require minimal supports or no supports at all when 3D printed. These structures exist in stable form in nature, like butterfly wings are made of Gyroids. Automotive and aerospace industry have a growing demand for strong and light structures, which can be solved using TPMS models. In this research we will try …

Contributors
Raja, Faisal, Phelan, Patrick, Bhate, Dhruv, et al.
Created Date
2019

A numerical study of chemotaxis in 3D turbulence is presented here. Direct Numerical Simulation were used to calculate the nutrient uptake for both motile and non-motile bacterial species and by applying the dynamical systems theory the effect of flow topology on the variability of chemotaxis is analyzed. It is done by injecting a highly localized patch of nutrient in the turbulent flow, and analyzing the evolution of reaction associated with the observed high and low stretching regions. The Gaussian nutrient patch is released at different locations and the corresponding nutrient uptake is obtained. The variable stretching characteristics of the flow …

Contributors
George, Jino, Tang, Wenbo, Peet, Yulia, et al.
Created Date
2017